************************************************************ Day: (2024\10\26) Time: ( 6:13:47) SlotNo:1 MP ver:V0205 MPBinType:63.0 RDTBinType:63.0 Test Station:EraseMP Check RDT Table:0 INI file:C:\Users\Usuario\Desktop\AS_SSD_MP_Tool_V0205\INI_files\ini_SanDisk(45)\SanDisk_BiCS3_8T_45 3c 98 b3 76 72 0b.INI ************************************************************ Serial Number write to infoblock: 000000000003 UI CHCE Map : 0 Drive Letter are Locked. IC Ver: AS2258 [ Success ] Check ICVer. OK, Total take 0.047 sec. ROM mode 45 3c 98 b3 76 72 0d Get CE Map=0, AutoCapacity_DynamicCE_En=1 Scan all ID : CE_00: 45 3C 98 B3 76 72 0D 0E CE_01: 00 00 00 00 00 00 00 00 CE_02: 00 00 00 00 00 00 00 00 CE_03: 00 00 00 00 00 00 00 00 CE_04: 45 3C 98 B3 76 72 0B 0E CE_05: 00 00 00 00 00 00 00 00 CE_06: 00 00 00 00 00 00 00 00 CE_07: 00 00 00 00 00 00 00 00 CE_08: 45 3C 98 B3 76 72 0D 0E CE_09: 00 00 00 00 00 00 00 00 CE_10: 00 00 00 00 00 00 00 00 CE_11: 00 00 00 00 00 00 00 00 CE_12: 45 3C 98 B3 76 72 0B 0E CE_13: 00 00 00 00 00 00 00 00 CE_14: 00 00 00 00 00 00 00 00 CE_15: 00 00 00 00 00 00 00 00 Copy Temperature log 64 bytes Read RDT Info from BBT Issue ReadRDTInfo Command Failed !!! Reset Temperature log 64 bytes [ Success ] Verify param.ini with Device Info OK- Total take 2.578 sec. Run info CE map=0 [ Success ] Force To Boot Code OK.- Total take 0.312 sec. .\FW\MP\15002C002_000005.bin Vender_Send_Seed done. ISPProgramPRAM_loop:0 done. ISPProgramPRAM_loop:1 done. ISPProgramPRAM_lasted done. ISPProgramPRAM_lasted done. ISPProgramPRAM_lasted done. ISP Program ICCM/DCCM done. Vender_Check_CRC done. Vender_Check_CRC done. Vender_Check_CRC done. Vender_Check_CRC done. Check CRC done. Get CE Map=0, AutoCapacity_DynamicCE_En=1 [ Success ] ISP Program PRAM OK- Total take 7.187 sec. Original CE Map=0, UI CE Map=0, Compare=0 Set CE Map=0 Scan_Flash_SDLL: Get CE Map=0, AutoCapacity_DynamicCE_En=1 DiePerFlash=1, SectorPerPage=32 Ch=0~1, Bank=0~1 FLH_IF=3 Flh_Clk=7 FlashMode : 3 FlashClock : 7 FlashODT : 0 Flash(NAND)Drive : 0 PadODTEnable : 0 PadODT : 0 PADDriveEnable : 0 ALEPads : 0 CLEPads : 0 WEPads : 0 REPads : 0 FRDYPads : 0 WPPads : 0 DQSPads : 0 DataPads : 0 CEPads : 0 ScanRound : 0 Scan Interval : 0 Scan_LDPC_Error_Bit : 0x03FF Set Scan Window Criteria : 50 Duty Range : 0~0 Duty : 0 Bank : 0 Die : 0 CH 0 Read-Min : 0 Read-Max : 131 Write-Min : 3 Write-Max : 120 CH 1 Read-Min : 0 Read-Max : 130 Write-Min : 3 Write-Max : 125 Duty : 0 Bank : 1 Die : 0 CH 0 Read-Min : 0 Read-Max : 131 Write-Min : 2 Write-Max : 120 CH 1 Read-Min : 0 Read-Max : 131 Write-Min : 2 Write-Max : 127 CH0 Read : Duty_0: CH_0: Read_Min : 0 Read_Max : 131 (Range : 132) CH1 Read : Duty_0: CH_1: Read_Min : 0 Read_Max : 130 (Range : 131) CH0 Write : Duty_0: CH_0: Write_Min : 3 Write_Max : 120 (Range : 118) CH1 Write : Duty_0: CH_1: Write_Min : 3 Write_Max : 125 (Range : 123) Find Read Max Duty :Ch_0 Duty_0 Ch_1 Duty_0 [Windows]: Duty_0 CH_0: Read Window=0x41, Write Window=0x3d Duty_0 CH_0: HW_Rd=0x45, HW_Wr=0x45 ScanValueRe[0] = 0x8004 ScanValueWr[0] = 0x8008 Duty_0 CH_1: Read Window=0x41, Write Window=0x40 Duty_0 CH_1: HW_Rd=0x45, HW_Wr=0x45 ScanValueRe[1] = 0x8004 ScanValueWr[1] = 0x8005 [ Success ] Scan Window Process OK- Total take 0.984 sec. [ Success ] Force To Boot Code OK.- Total take 0.313 sec. .\FW\MP\15002C002_000005.bin Vender_Send_Seed done. ISPProgramPRAM_loop:0 done. ISPProgramPRAM_loop:1 done. ISPProgramPRAM_lasted done. ISPProgramPRAM_lasted done. ISPProgramPRAM_lasted done. ISP Program ICCM/DCCM done. Vender_Check_CRC done. Vender_Check_CRC done. Vender_Check_CRC done. Vender_Check_CRC done. Check CRC done. Get CE Map=0, AutoCapacity_DynamicCE_En=1 [ Success ] ISP Program PRAM OK- Total take 7.140 sec. [ Success ] eFuse Info UART : Enable JTAG : Enable Trim good die : 01 Get Controller ID : 12_19_0D_05_06_22_02 Trim good die : 01 Y Coordination : 12 X Coordination : 19 Wafer ID : 0d Lot ID 4 : 05 Lot ID 3 : 06 Lot ID 2 : 22 Lot ID 1 : 02 CTL Version : 03 [ Success ] Check eFuse OK, Total take 0.188 sec. Get CE Map=0, AutoCapacity_DynamicCE_En=1 Do SDR Write/Read Test, SDR Size= 32 MB [ Success ] DMA Write_Read SDR test ok, Total take 54.469 sec. Original CE Map=0, UI CE Map=0, Compare=0 Set CE Map=0 Do EraseAll Block, Type=0x09 [ Success ] Full Erase All Block OK(09)- Total take 15.547 sec. Start Scan Bad Block Progress ... Set EarlyBad_Spec= 0 per CE Die Per Flash= 1; Plane Number = 2; Max Block Per CE= 2956; Get Max Bad block number Percent= 10 Get Max Bad block number per Plane= 147 FlashNumber=4, MaxBad_perPlane/Die=147 Get CE Map=0 Issue ReadRDTInfo Command Failed !!! Find BBT parameter Read BBT checksum:eda5 CENo_0/Die_0-> Early Bad Count: Plane0=4, Plane1=29 CENo_4/Die_0-> Early Bad Count: Plane0=10, Plane1=10 CENo_8/Die_0-> Early Bad Count: Plane0=16, Plane1=20 CENo_12/Die_0-> Early Bad Count: Plane0=9, Plane1=60 [ Success ] Scan Bad Process OK- Total take 13.875 sec. InfoBlock Reset Temperature log 64 bytes MPver 00 02 05 00 05 Select AutoCapacity_MaxBadPercent_4CE FLH_IF=3 Flh_Clk=7 Get AutoCap_DynamicCE_En=0 Run Info CE map=0, CE map=0 flash num=4, ssd size=234441648, m_PhysicalSize=131072 Two Pass Program Type = 0 [ Success ] Modify InfoBlock OK. Do PreFormat: [ Success ] PreFormat-WriteInfo process OK.- Total take 25.406 sec. .\FW\MP\15002C002_000005.bin New Bin Type = 63.0 [ Success ] ISP Normal Firmware OK- Total take 0.328 sec. 45 3c 98 b3 76 72 0d Get CE Map=0, AutoCapacity_DynamicCE_En=1 [ Success ] Check InfoBlock progress OK. Copy-Compare Test Start: Flash Num=4, Logical Size=114473 MB Write begin 18 MB Area1: start LBA=0x0, End LBA= 0x9600 Write End 18 MB Area2: start LBA=0xdf8abb0, End LBA= 0xdf941b0 Read_Compare_Clear begin 18 MB Read_Compare_Clear End 18 MB [ Success ] Copy-Compare Test OK- Total take 122.843 sec. Start Scan Bad Block Progress ... Set EarlyBad_Spec= 0 per CE Set LaterBad_Spec= 0 per CE Die Per Flash= 1; Plane Number = 2; Max Block Per CE= 2956; Get Max Bad block number Percent= 10 Get Max Bad block number per Plane= 147 FlashNumber=4, MaxBad_perPlane/Die=147, Max.Later Bad=0/CE Issue ReadRDTInfo Command Failed !!! Find BBT parameter OB + OLB Count = 158 RDT Bad Count = 0 Later Bad Count = 0 All Good Blk Count = 11666 CENo_0/Die_0-> Channel:0,EarlyBad:Plane0=4,Plane1=29 CENo_0/Die_0-> Channel:0,LaterBad:Plane0=0,Plane1=0 CENo_4/Die_0-> Channel:0,EarlyBad:Plane0=10,Plane1=10 CENo_4/Die_0-> Channel:0,LaterBad:Plane0=0,Plane1=0 CENo_8/Die_0-> Channel:1,EarlyBad:Plane0=16,Plane1=20 CENo_8/Die_0-> Channel:1,LaterBad:Plane0=0,Plane1=0 CENo_12/Die_0-> Channel:1,EarlyBad:Plane0=9,Plane1=60 CENo_12/Die_0-> Channel:1,LaterBad:Plane0=0,Plane1=0 [ Success ] Scan Bad Process OK- Total take 0.235 sec. [ Success ] Check InfoBlock progress OK. [ Success ] GoodCard Mark OK. SMART_Return_Status: Out Reg:[0][c2][a0][50][0][0] Original Capacity (Identify): 114473 MB [ Success ] StandBy. [ Success ] PreTest-Initial Process Total take(sec): 276.250 sec. [ End ] Time: ( 6:18:24)